5.7 Vortec 1998 Chevy 5.7 Head Bolt Torque Specs

Heads are assembled with NEW 202 Stainless Steel ONE piece Intake valves. You torque 46 ft lbs long bolts 43 ft lbs for short boltsthen you make second pass on all bolts tighten them additional 90 degrees using a torque angle meter.

How To Correctly Torque Head Bolts Youtube

Discussion Starter 1 Sep 18 2009.

. I know I used it it with a new set of GM head bolts when I did mine. It states tighten all 11mm bolts to 22ftlb then all 11mm bolt additional 90 degrees then bolts 1-8 an additional 90 degrees and bolts 9 10 an additional 50 degrees and all 8mm bolts to 22ftlb. 106 INCH POUNDS 3 rd.

Have to go with the inch torque first as the foot pounds 38 wrench cant torque under 10lbs. 57 cylinder head installation I thought Merc published an alternative 3-step torque spec vs the prefered angle method for vortec heads. Went 30 then 50 then 70 ftlbs.

It had a displacement -- the amount of air and fuel exited from an engine during a full cycle --of 5735 cubic centimeters and compression ratio -- the maximum engine volume compared to the. Heads are assembled with NEW 160 Stainless Steel ONE piece Exhaust. The intake port of the Vortec head is different and measures 160cc with a modified port that increases the flow velocity.

I would just like to see if anyone know where I might find a printable version. Also the sequence would help too. I cant access the service manual to look but thought it was 31 or possibly a service bulletin.

Camshaft sprocket bolt 18 ft. I am looking for the torque specs for a 96 57 vortec cylinder head. I have a 2000 Tahoe with a 57L and am replacing head gaskets.

This is the Head Bolt Torque Sequence Pattern for the Small Blocks Mouse Motors. The idea is the iron block and heads will want to move around differently compared. The intake bolt pattern is different and utilizes an eight-bolt attachment.

Joined Nov 29 2007. Step 2 additional 70 degrees. 1998 chevy astro 43 v6 torque specs include.

Cylinder Head Bolt Optional On-Vehicle Stategy. GM 57L-350ci-V8 Engine Torque Specs. Torque specs for the lower intake manifold57 litrevortec.

Here is the issue I did not catch the fact the head bolts are TTY. 61 INCH POUNDS 2nd. Over 6000 Automotive Torque Specs.

Step2 additional 35 degrees. Vocational Technical or Trade Scho. What is the difference in 1994 57 350 and 1998 vortec 350 heads.

I am looking for the torque specs for the lower intake manifold on a 1999 57 litre chevy vortec engineplease I need help. I just cleaned and used thread sealer. Search Car Torque Specifications by Engine or Model.

More than that will destroy the gaskets and they will leak. What are the head bolt torque specs for a. I know starting from the center and working your way out.

The factory specs are 132inlb for the intake to head 88inlb for the upper in steps 27106132 4488 The heads are 22ftlb first Short 55 Med 65 Long 75 The pattern is the traditional from the center out of all SB engines Reusing the stock head bolts is is fine see below From AERA Cylinder Head Installation On 1996-99 GM 57L VIN R Engines. The torque is 3 then 12 then 15 Newton-meters with blue Loctite on clean bolts and clean threads. Crankshaft oil deflectorboltnut 27 ftlbs.

Firing Order 1-8-4-3-6-5-7-2 Spark Plug Gap 152 mm 0060 in 42 kPa at 60 psig at 1000 engine rpm 1000 engine rpm Oil Pressure Minimum at Normal Operating Temperature 125 kPa at 180 psig at. I recently did a re-ring and bearing on a great running 57 Chevy small block. 185 CC intake runners.

Balance shaft if equiped gear bolt step 1 15 ftlbs. Only show this user. The Chevy 57L Vortec engine was paired with a General Motors electronic four-speed automatic transmission 4L60E.

I have a service manual but it is not very accurate. Crankshaft damper bolt 74 ft. It is rated at 255 horsepower at 4600 rpm and 330 foot-pounds lb-ft of torque at 2800 rpm.

Tighten in an x-pattern in bolts then outer bolts. Towing with a 57L Vortec Engine. Or what ever you might lovingly call this motor.

It had 150000 miles on it. My engine swap 372 Motor I put into my International Scout. The bolt holes that are in the head were the intake manifold bolts go.

Performance Specifications The Vortec generated 255 horsepower at 4600 rpm and 330 foot-pounds of torque at 2800 rpm or the force required to move a vehicle forward. Up to 25 cash back TORQUE SPECIFICATIONS TORQUE SPECIFICATIONS 43L 50L 57L Application Ft. NEW PAIR of aftermarket GM CHEVY VORTEC 350 V8 57 OHV CAST IRON PERFORMANCE CYLINDER HEADS 202 STAINLESS VALVES 906 062 1996 2000.

The engine was out of a 1998 1500 Silverado with a rusty frame. I have not had a lot of vehicles with Small Block Chevys other then. 64 CC combustion chambers.

Nm Balance Shaft Gear Bolt Step 1 15 20 Step 2 Additional 35 Degrees Bellhousing Bolt 35 47 Camshaft Sprocket Bolt 18 25 Connecting Rod Cap Nut 43L Step 1 20 27 Step 2 Additional 70 Degrees 50L 57L Step 1 20 27 Step 2. Specifications Fastener Tightening Specifications Specification. Head torque on a 57 vortec.

57 Vortec Heads and Regular 350 Heads. GM Engine Torque Specifications and Sequences GM Engine Torque Specs Orders may take longer than usual to process due to manufacturers having issues receiving and shipping parts. This does not include specs for LSX or Aluminum.

Connecting rod cap step 1 20 ft. The bowl area is wider around the guide compared with regular 350 heads. The 22 engine top bolts from left to right is 8-4-1-5-9-your bottom bolts left to right is 7-3-2-6-10 this is your torque sequenceyou need to use bolt thread sealerwait 15 minutes before putting bolts in.

Foot pounds. In 1995 vortec heads still used TBI injection with the top end of the engine being vortec head and intake mainfold.

Jegs High Performance